Cylinder Power Balance Testing – Uncover Hidden Engine Issues

If the vehicle has coils that share cylinders (waste spark system). Then, you can place a 1″ (25-mm) section of vacuum hose, between each coil tower and spark plug wire. Then, connect a alligator clip, from a non powered test light, to a good engine ground. Next, touch the tip of the test light, to each length of vacuum hose, to short out each spark plug.

Thank You !


Cylinder power balance testing, has many options. So, if the engine has individual ignition coils (COP) on each spark plug. Then, you can disconnect the primary electrical connector, which will shut off the spark to the spark plug.

(COP) Coil On Plug Ignition Coil
(COP) Coil On Plug Ignition Coil

Visually inspect the engine to determine the best method, to disable the cylinders. For example, this may include, connecting a scan tool, installing vacuum lines on each coil or removing spark plug wires. If necessary, disable the idle control system:

  • Start the engine and allow it to idle. Now you will need to record the idle (rpm).
  • Using the method chosen to disable cylinders, disable the first cylinder and record the (rpm).
  • Reactivate the cylinder and allow the engine to run for approximately 10 seconds to stabilize.
  • Repeat the steps on each of the cylinders and record your readings. Determine any necessary actions.
You Will Need To Record The Idle (RPM)
You Will Need To Record The Idle (RPM)


Doing cylinder power balance testing, is one of the best and easiest ways, to find the source of problems. Engine misfires can be fairly random and if spaced far enough apart, they should not cause any harm. But, a frequent or steady misfire, will cause a sharp rise in, unburned hydrocarbon emissions.  As a result, you could see, a noticeable drop in power and a significant decrease, in fuel economy.

Cylinder power balance testing, involves disabling one cylinder at a time, then recording the (rpm). Consequently, you can perform a cylinder power balance test, several different ways.

Firstly, you will need to decide whether, to disable the ignition or the fuel, to each individual cylinder. If the engine has port fuel injectors that are accessible. Then, disconnecting the electrical connector from each fuel injector one at a time, will shut off the fuel. If the ignition system is disabled for a cylinder, the fuel will still be delivered. But, will not be burned in the cylinder.

Consequently, this may cause it to burn, in the catalytic converter, which can cause it to overheat and possibly be damaged. Therefore, shutting down the fuel is preferable, if it is an option.

That’s why, comparing the test results, from other tests, will help you learn more about the problem:

Cylinder Power Balance Testing - Uncover Hidden Engine Issues
Cylinder Power Balance Testing – Uncover Hidden Engine Issues

So, performing a cylinder power balance test can help uncover, hidden engine issues, commonly missed with other tests.

Cylinder power balance testing, can find issues related to, engine misfires, lack of power, or just a poor running engine.

Furthermore, cylinder power balance testing is often used along with, a cylinder compression and cylinder leakage test, to further pinpoint the problem.

However, if the vehicle has a distributor, disconnect one spark plug at a time, from the distributor cap. Furthermore, it’s a good idea to use a test lead, to ground the spark at the distributor cap terminal. Also, doing this will help prevent the spark from damaging the ignition module. Because, it shuts down the spark, for the cylinder being tested.

How To Perform A, Cylinder Power Balance Test

For many OBD-II vehicles, you can identify, which cylinders are misfiring, by using a scan tool. Just access stored diagnostic trouble codes (DTCs), in the (PCM). You can also access mode 6 data, which will give you information on how prevalent misfires are, on each cylinder.

In some cases, you can use the scan tool, to command the (PCM) to perform an automatic cylinder power balance test. And, report the results, right on the scan tool. So, on most newer vehicles, using the scan tool is by far, the best method of performing, a cylinder power balance test.

But, if The System Is Not Setup To Perform The Test Automatically, You Will Have To Do It Manually

Manual Cylinder Power Balance Testing
Manual Cylinder Power Balance Testing

Finally, by comparing the results, of each one of these tests to each other. You can identify what, may or no be the problem.

So, knowing each of the options, will allow you to choose the easiest one, for the vehicle you are diagnosing:

  • The capabilities of the (PCM).
  • The ease of accessing the required components.
  • Also, the tools you have available for the job.
(OBD) Engine Code Reader
(OBD) Engine Code Reader

So, cylinder power balance testing, is quick and easy to perform. And, it identifies, any cylinders that have problems. But, the results of this test alone, do not specify, what the problem is.